Total 4731 registered members
Top
Comment
sep
sep
sep
Email It!

The Nature Of Reactive Energy

1,884 views

The Nature Of Reactive Energy

The Nature Of Reactive Energy

All inductive machines i.e. electromagnetic and devices that operate on AC systems convert electrical energy from the powersystem generators into mechanical work and heat. This energy is measured by kWh meters, and is referred to as active or wattful energy. In order to perform this conversion, magnetic fields have to be established in the machines, and these fields are associated with another form of energy to be supplied from the power system, known as reactive or wattless energy.

The reason for this is that inductive plant cyclically absorbs energy from the system (during the build-up of the magnetic fields) and re-injects that energy into the system (during the collapse of the magnetic fields) twice in every power-frequency cycle.

The effect on generator rotors is to (tend to) slow them during one part of the cycle and to accelerate them during another part of the cycle. The pulsating torque is stricly true only for single-phase alternators. In three-phase alternators the effect is mutually cancelled in the three phases, since, at any instant, the reactive energy supplied on one (or two) phase(s) is equal to the reactive energy being returned on the other two (or one) phase(s) of a balanced system. The nett result is zero average load on the generators, i.e. the reactive current is “wattless”.

An exactly similar phenomenon occurs with shunt capacitive elements in a power system, such as cable capacitance or banks of power capacitors, etc. In this case, energy is stored electrostatically. The cyclic charging and discharging of capacitive plant reacts on the generators of the system in the same manner as that described above for inductive plant, but the current flow to and from capacitive plant is in exact phase opposition to that of the inductive plant. This feature is the basis on which powerfactor improvement schemes depend.

It should be noted that while this “wattless” current (more accurately, the wattless component of a load current) does not draw power from the system, it does cause power losses in transmission and distribution systems by heating the conductors.

In practical power systems, wattless components of load currents are invariably inductive, while the impedances of transmission and distribution systems are predominantly inductively reactive. The combination of inductive current passing through an inductive reactance produces the worst possible conditions of voltage drop (i.e. in direct phase opposition to the system voltage).

Active and reactive power

Fig. 1 : An electric motor requires active power P and reactive power Q from the power system

For these reasons, viz:

  • Transmission power losses and
  • Voltage drop

The power-supply authorities reduce the amount of wattless (inductive) current as much as possible. Wattless (capacitive) currents have the reverse effect on voltage levels and produce voltage-rises in power systems.

The power (kW) associated with “active” energy is usually represented by the letter P. The reactive power (kvar) is represented by Q. Inductively-reactive power is conventionally positive (+ Q) while capacitively-reactive power is shown as a negative quantity (- Q). S represents kVA of “apparent” power.

Figure 1 shows that the kVA of apparent power is the vector sum of the kW of active power plus the kvar of reactive power.

Alternating current systems supply two forms of energy:

  • Active energy measured in kilowatt hours (kWh) which is converted into mechanical work, heat, light, etc
  • Reactive energy, which again takes two forms:
    • “Reactive” energy required by inductive circuits (transformers, motors, etc.),
Plant and appliances requiring reactive energy

All AC plant and appliances that include electromagnetic devices, or depend on magnetically-coupled windings, require some degree of reactive current to create magnetic flux. The most common items in this class are transformers and reactors, motors and discharge lamps (i.e. the ballasts of).

The proportion of reactive power (kvar) with respect to active power (kW) when an item of plant is fully loaded varies according to the item concerned being:

  • 65-75% for asynchronous motors
  • 5-10% for transformers

SOURCE: Schneider Electric

.

Related articles


Be nice and share this article with others! How to use all these nice buttons?

Del.icio.us Digg Mixx Reddit Technorati Linkedin Email this post Save to Google bookmarks Save to Yahoo Buzz Save to Reddit Save to Technorati
Tell us what you're thinking about article you just read.

Turn Your Thoughts Into Words

Tell us what you're thinking... we care about your opinion!
and oh, not to forget - if you want a picture to show with your comment, go get a free Gravatar!

*



Comments

2 Responses to “The Nature Of Reactive Energy”

    Trackbacks

    Check out what others are saying about this post...
    1. Story added…

      Your story was featured in Save this link dot Net! Here is the link to vote it up and promote it: http://www.savethislink.net/Technology/The_Nature_Of_Reactive_Energy...

    2. [...] This post was mentioned on Twitter by Electric Engineering, Electric Engineering. Electric Engineering said: The Nature Of Reactive Energy http://lnkd.in/6DA_tt [...]